Reasons Why Furrion Oven Does Not Stay Lit- Easy Fixing Guide

It makes no difference whether your furrion oven is built by Domestic, Suburban, or Magic Chef; if you’re not sure where to start, furrion oven troubleshooting can be a serious hassle. Fortunately, there are a few simple things you can do to avoid having to visit the mechanic – and also avoid paying for dinner.

The answer you seek will be distinct to you and will depend on the issue you’re having – such as with the pilot flame dimming on you or no lighting at all. This guide contains remedies to these and other often encountered furrion oven issues.

While preparing dinner, the last thing to think about is troubleshooting your furnace, but if something does go wrong, that is exactly what you will find yourself doing. I’ve saved you the time and effort of browsing Furrion forums for answers to your oven difficulties, letting you be late for the meal. Read along;

Reasons why a Propane Oven does not stay lit

Reasons why a Propane Oven does not stay lit

Propane heaters are a reliable and cost-effective method of maintaining a suitable temperature in any room. They, like any other machine, may, however, have troubles from time to time. Regrettably, there will be times when the gas heater simply will not stay lit for whatever reason. What would you want to do if your propane heater becomes unresponsive?

If you want to know about these heaters, check the Propane heater from Amazon.  

When a propane heater fails to stay lit, it is usually so because the propane heater senses that the flame is failing in some way, triggering the gas heater’s safety measures and causing it to shut down. It is probable that the issues are caused by a genuine fault or by a sensor malfunction.

Check to verify if the sensor device is completely consumed by the flame, or try polishing it with sandpaper to determine if this is the case. This may assist you in resolving the problem with the propane heater.

Most propane heater problems can be attributed to a defective pilot light. If your gas heater uses a free-standing pilot light, it should be evident through a small opening or aperture near the control knob. The pilot should stand about an inch tall and be mostly blue in color. Unless the pilot tube is wavering or split, or is small and yellow or orange in color, cleaning it is not necessary.

You can clear it out by first turning off the gas and then delicately inserting a needle with your finger into the tube’s top. Additionally, a draft may cause problems with the propane heater’s pilot, in which case the best approach is to identify and eliminate the draft source. Another option is that the problem is with the thermocouple.

The thermocouple is a temperature-sensitive protection measure that prevents unburned gas from being produced in a combustion chamber or boiler. The thermocouple is heated by the pilot flame, signaling the valve to stay open and keep the pilot burning, and the propane heater running properly.

If the thermocouple is set too far away from the flame, it can cause the pilot to go out and the propane heater to switch off; however, this is easily corrected by repositioning the thermocouple closer to the fire.

Also, it is likely that the thermocouple has deteriorated, in which case it must be replaced. Replace with a new one by unclipping the bulb, disconnecting the wiring from the gas valve, and gently removing the existing one before installing a new one. Always turn off the electricity as a precaution.

A malfunction of the electrical spark mechanism might be the cause of the issue. When the compressor is turned on, the burner chamber should glow with a flame. If you do not have one, you can get an electrical chart of the apparatus, which is typically included with the instruction manual, and use it to isolate the cause of the problem.

Similarly, if the propane heater flashes but does not light, the gas cylinder that supplies it may be empty or the gas has been turned off. Confirm accuracy, and if the issue persists, wipe the gas valve lightly with a needle to verify it is clean.

Furrion camper oven lighting

Furrion camper oven lighting

For your stove, push the knob and rotate it to the pre-set flame. Maintain continuous pressure and hold on to the knob while pushing and holding on to the start button. A clicking sound should be audible, and the flame now starts to ignite. Adjust the knob to the ideal range after the light is switched on. It is necessary to repeat the process for each burner.

With regards to the Furrion Oven, adjust the knob to the desired flame setting by pressing down on it. Maintain continuous pressure and hold on to the knob while pushing and holding on to the start button. You will notice a clicking sound in the oven’s back and see a faint blue flame after the pilot light turns on.

Allow approximately 30 seconds for it to burn before turning it to broil in order to guarantee that flames are evident throughout the ring. If everything looks to be in order, adjust the oven temperature dial to the desired setting. When you turn on your devices for the first time on the first day of your trip, they will take longer to come to life since the gas will have to go further to reach the oven.

Additionally, each time you refill your LP tank, you will need to press for an extended period. Your pilot may take between 30 and 60 seconds to illuminate. It is necessary for the pilot to reach a suitable temperature after ignition in order to keep its hold.

How to replace a thermocouple in an RV oven

To begin, turn off the oven’s gas supply and remove the malfunctioning thermocouple. Screw the new thermocouple into the same area as the previous one. Keep an eye on the clips that secure the thermocouple in place as you remove and replace them.

Both tasks will require a few simple tools. These include; 

  • A small flexible screw,
  • A small screwdriver, or
  • A flashlight.

Preserving the safety of your family comes first, which is why the first step is to turn off the gas supply to the oven by locating and turning off the valve that supplies gas to it.

Here is a quick table;

Steps on how to replace a thermocouple in an RV oven.


Essential product

  • Press down the gas pedal

To cut off the gas supply; to ensure it’s not working

Check the Oven gas regulator from Amazon.

  • Locate and remove the old thermocouple

To replace it with a new one

Nut wrench.


  • Install the new thermocouple.

To troubleshoot the RV oven; enhance the effectiveness

Check this Thermocouple from Amazon.

1. Press down the gas pedal until it comes to a complete stop

It is labeled on the major gas pipeline that connects to the oven’s regulator gas valve. It is equipped with a schematic and an open/close button. Simply rotate it parallel to the main pipe, and you’re done.

Next, locate the oven’s gas regulator. A square metal component with a handle is located at the back of the gas oven. You’ll eventually find it if you follow the primary gas pipeline into the back of the building.

2. Locate and remove the old thermocouple

It is connected to the regulator via an octagonal copper tube with a tiny nut at one end. It runs down the oven’s body. After loosening the nut with a wrench, disconnect the copper tubing from the gas valve. At this point, use the screwdriver to remove the screws holding the thermocouple in place. Before disconnecting, the clip should be carefully removed.

3. Install the new thermocouple

Ensure that the old thermocouple is free of debris or filth before replacing it with a new one. When purchasing a replacement thermocouple, keep the old one on hand.

Reattach the copper tubing to the regulator unit by tightening the nut on the copper tubing. While RV ovens are primarily powered by propane, many of them also include automated igniters and display screens that are powered by electricity. This is not a problem if you are connected to shore power.

How to easily determine if the fuse in your RV’s oven is blown

How to easily determine if the fuse in your RV's oven is blown

If the RV oven does not light and any electrical controls do not work properly, the main fuse box should be located. Then you’ll need to locate the oven’s fuse. Before replacing the fuse, disconnect it and inspect it for any black spots or clearly damaged connections inside.

If it is clearly blown, replace it with a new one of the same size. A blown fuse or tripped circuit breaker is frequently to blame for appliances such as the oven, stove, or clock outlet malfunctioning. Fortunately, as expressed in the preceding paragraph, it is easily identifiable.

You may also find the following article helpful: RV Microwave Not Working With Generator- Ways You Can Fix.


In summary, we discussed how to ignite the pilot light on an RV oven and what to do if your RV oven will not turn on at all in this troubleshooting article.

Additionally, we discussed how to reset and replace the thermocouple in your RV oven. The guide has also addressed how to tell if the fuse in the oven of your RV has blown in the final segment. Hope the article helped you solve your problems. 

Leave a Comment